Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Parts & Accessories

Stan's NoTubes Presta Removeable Valve Core
$5.95
Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.
Wolf Tooth Components Fat Thru Axles
$74.99
The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA - 7075 T6 Aluminum
Shimano Alfine SG-S700 Left Hand Cone with Dust Cap
$19.99
If the bearings are getting rough on your Shimano Internally Geared hub, it could simply be a matter of replacing a pitted cone and repacking the bearing with grease. - Fits left side of Alfine SG-S700 hubs
Stan's NoTubes Schrader to Presta Valve Hole Reducer
$2.95
- Schrader-Presta, Rubber Valve Hole Reducers - For using a Presta rim strip in a Schrader drilled rim. - Sold individually
DT Swiss Tubeless Ready Rim Tape
$35.01
DT Swiss tubeless-ready tape seals the rim for tubeless applications and also works well as rim tape for tube-type setups. - Durable adhesive tape works as a rim tape and airseal
WeThePeople Helix Hub Guard
$35.99 - $44.99
When you own a freecoaster as good as the Helix, you're going to want to keep it protected. WTP's Helix hub guards work on the non-drive side of the Helix freecoaster and replace the cones for a perfect fit without having to spread your dropouts. - Fits Helix V1 and Helix V2 freecoaster hubs - Available in 7075-T6 alloy or Nylon Fiberglass - Comes with heat-treated chromoly adaptor to replace hub cone nuts for perfect fit
WeThePeople Supreme Hub Guards
$35.99
WeThePeople's Supreme Hub Guards are made of low-friction nylon fiberglass. Simply replace the cones on your Supreme Front and Cassette Hubs for a perfect fit without having to spread your dropouts. Available for both front and rear. These guards now feature a heat-treated chromoly insert for longer life.
Kink Universal Driver Guard
$49.99
The Kink Universal Driver guard is designed to fit most modern freecoaster and cassette hubs using either an 8T or 9T driver. The guard is made from heat-treated chromoly steel, giving it a ton of strength and long lifespan. The slim chromoly design means it can slide between your existing hub hardware and dropout, which allows for easy installation with only a wrench or socket to loosen and tighten axle nuts
Stan's NoTubes Alloy Tubeless Valve Stems - Long
$46.95 - $59.95
Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.
DT Swiss Pro Head Brass Nipples
$27.99
Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.
DT Swiss Standard Aluminum Nipples
$24.99 - $66.99
The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples
DT Swiss Narrow Base Tubeless Valve
$16.47
Tubeless valves for DT Swiss rims for repair or replacement.
Stan's NoTubes Alloy Tubeless Valve Stems - 44mm
$36.95
Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.
Wheels Manufacturing Inc. CN-R082 Cone
$14.99
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: Sovos 9mm x 1, front hub - Compatible with 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 15.0mm - Length: 12.8mm - 1 cone per bag COMPATIBLE HUBS: - Sovos 9mm x 1, front hub - Taiwanese and similar front hubs with 9mm x 1 axle
DT Swiss Pro Head Spoke Reinforcement Washers for SPLINE One
$24.99
Pro Head Reinforcement System (PHR) has a larger and more spherical contact area and is designed to balance loads transferred to the rim. The PHR system acts as a ball and socket interface, allowing the spoke to pivot into alignment while maintaining even, consistent contact during installation in order to follow the perfect trajectory from the hub to the rim.
Zefal Rim Tape
$9.95
- Strip of Rim Tape. - Length : 2 meters. - Made of cotton. - Sold by Pair.
Stan's NoTubes Neo OS Front Hub Torque Caps
$35.99
Front RockShox/SRAM-specific Torque-Cap 15mm through-axle SealLock end caps for Neo OS and Neo Ultimate OS hubs. SealLock end caps feature a low-friction U-cup seal that snaps into place and stays secure even when your wheel is removed from your bike. Torque-Cap end caps have the same 15mm inside diameter as other systems, but outside diameter is larger (31mm), making these end caps only compatible with Torque-Cap-compatible forks. Note: Torque caps are not compatible with centerlock hubs.
RockShox Maxle Ultimate Rear Thru-Axle
$92.95 - $96.99
The tool-free Maxle Ultimate Rear brings exceptional stiffness and durability to your ride in a high clamping force, easiest-to-use internal cam thru axle system.
DT Swiss RWS MTB Front Thru Axle
$52.99
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and to perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening
Stan's NoTubes Rim Tape
$25.99 - $39.99
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
Stan's NoTubes Threaded Valve Extenders
$39.95
Stan's Threaded Valve Extenders let you convert deep-section rims to tubeless. They're precision-machined from aluminum and are designed to fit deep-dish carbon and aluminum rims. And, they're threaded on the outside so you can install the Presta lock-ring nut for a perfect seal.
WeThePeople Helix Driver Guard
$35.99 - $49.99
When you own a freecoaster as good as the Helix, you're going to want to keep it protected. WTP's Helix driver guards work on the drive side of the Helix freecoaster and replace the cones for a perfect fit without having to spread your dropouts. - Fits Helix V1 and Helix V2 freecoaster hubs - Available in 7075-T6 alloy or Nylon Fiberglass - Comes with heat-treated chromoly adaptor to replace hub cone nuts for perfect fit
DT Swiss RWS MTB Rear Thru Axle - X-12 System w/Plug-in Lever
$72.99
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Conical X12 washer, compatible with Syntace X-12 system - Removable, plug-in lever design is streamlined and protects your RWS lever - Thread Pitch: 12 x 1.0mm
WeThePeople Cassette Hub Driver
$99.99
- Cassette Body Type: Single Cog Driver - Drivetrain Speeds: Single Speed 1/2" x 1/8" - Material: Steel - Tooth Count: 9
Wolf Tooth Components Front Boostinator
$39.99
Boostinators are hub specific conversions designed to take non-boost hubs and convert them to boost compatibility. Don't toss out that wheelset - Boostinate it.
Stan's NoTubes Neo Speedsync Freehub
$199.99
Stan's original Neo hub has evolved to be stronger and more reliable than ever. The additional stress of larger cassette cogs, more capable bikes, and even more challenging trails led to the creation of the Neo with Speedsync. This CNC machined Speedsync freehub is a direct replacement for your Neo hub and includes pawls, springs, pawl retaining ring, and 2 red freehub spacers. Bearings are pre-installed. Note: - Singlespeed freehub cannot be used to convert a hub originally set up with a Shimano or Sram XD freehub to SS. This freehub is only to be used with Stan's Neo SS hubs. - OneUp freehub WILL NOT WORK with a SRAM cassette or Shimano cassette without a One Up Shark Cluster.
Wheels Manufacturing Inc. CN-R084 Cone
$14.99
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: Joytech 9mm x 26, front hub - Compatible with 9mm x 26 axle - Cone Wrench Size: 13mm - Threads: 9mm x 26 - Diameter: 15.0mm - Length: 12.8mm - 1 cone per bag - Note: O-ring / seal not included. COMPATIBLE HUBS: - Joytech 9mm x 26, front hub - Taiwanese hubs with 9mm x 26 axle - 105 SC 1055 8-speed Rear - 105 SC 1056 7-speed Rear - XT-II M732 7-speed Rear
Stan's NoTubes Neo Front Hub End Caps
$31.99
Front end cap conversion kits for NoTubes Neo and Neo Ultimate - SealLock end caps feature a low friction U-cup seal that snaps into place
Roval Boost Conversion Kit
$68.00
Convert Roval wheels with 142 or 142+ to be used with Boost spacing (110 /148mm) suspension forks and frames. - Kits include front and rear hub end caps, rotor spacers, and kit specific rotor bolts - Compatible with select MY13-16 Roval Wheels. Choose the appropriate SKU for each wheelset - Each conversion kit requires the existing rear wheel to be re-dished to center. Consult an authorized dealer to perform this operation
Wheels Manufacturing Inc. Outer Axle Nut
$1.50 - $10.99
Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually
Page 1 of 3 Next page